养护机械配件与维修

产品描述

 夯锤的知识分享：后排夯锤的下止点应和熨平板平或者比熨平板略低但不应超过0.5mm。后排夯锤下止点过高过低都会影响摊铺质量。夯锤越重，对桥台的振动影响越大，且夯沉量随夯击次数的增加而增大，合适的锤重和夯击次数可有效控制对桥台的动力影响；夯锤前挡板与夯锤间应有0.5 mm的间隙。间隙过小夯锤前挡板推料引起变形后会夹住夯锤使夯锤轴转动困难。间隙过大则容易进料，加快夯锤、夯锤前挡板、磨损条的 磨损，同时进料也会影响夯锤轴的转动。

免责声明丨 部分内容来源网络！本文仅供交流学习 , 版权归属原作者，部分图片、内容推送时未能及时与原作者取得联系，若来源标注错误或侵犯到您的权益烦请告知，我们将立即删除.

企业介绍

公司供应摊铺机配件，压路机配件，铣刨机配件，摊铺机刮板驱动轴，刮板驱动轴总成，找平仪，找平仪支架以及液压泵和配件。还供应摊铺机易损件，摊铺机平衡梁，搅龙轴，踏板，输料底板，叶片，熨平板，减速机，链轨，履带板，支重轮，刮板大链条，输料链条等。

联系人：梁经理

联系方式：13645201509（微信同号）

QQ：2870202745

QQ邮箱：2870202745@qq.com

网易邮箱：LS13645201509@163.com

WhatsApp:+86  13645201509

Knowledge sharing of chain wheel rammer on scraper: The bottom stop point of the rear rammer should be level with the ironing board or slightly lower than the ironing board but should not exceed 0.5mm. If the bottom stop point of the rear rammer is too high or too low, it will affect the paving quality. The heavier the rammer, the greater the impact on the vibration of the bridge pier, and the settlement of the rammer increases with the increase of the number of ramming times. Appropriate hammer weight and ramming times can effectively control the dynamic impact on the bridge pier; There should be a gap of 0.5 mm between the front baffle of the rammer and the rammer. If the gap is too small, the front baffle of the rammer will deform and clamp the rammer, making it difficult for the rammer shaft to rotate. If the gap is too large, it is easy to feed and accelerate the wear of the rammer, rammer front baffle, and wear strip. At the same time, feeding will also affect the rotation of the rammer shaft.

Disclaimer | Some content is sourced from the internet! This article is for communication and learning purposes only. The copyright belongs to the original author. Some images and content were not promptly contacted when pushed. If the source annotation is incorrect or infringes on your rights, please inform us and we will immediately delete it

Company Introduction

The company supplies paver accessories, roller accessories, milling machine accessories, paver scraper drive shaft, scraper drive shaft assembly, leveling instrument, leveling instrument bracket, hydraulic pump and accessories. We also supply vulnerable parts for pavers, including balance beams, agitator shafts, pedals, feeding base plates, blades, ironing plates, reducers, chain rails, track plates, support wheels, scraper chains, and feeding chains.

Contact: Manager Liang

Contact information: 13645201509 (same WeChat account)

QQ：2870202745

QQ email: 2870202745@qq.com

NetEase email: LS13645201509@163.com

WhatsApp:+86  13645201509